How to Vent a First-Floor Bath

Properly venting bathrooms not only transports smelly air outside the house, but it also transports humid air as well. If the bathroom vent simply connects to a different part of the house, then the humidity moves to another room and rots the wood and promotes mold growth. With first-floor bathrooms, you must install a duct through a closet or storage area above, allowing you to vent the bathroom air through the roof and outside the house.

Instructions

Shut off the electricity to the bathroom at the houses electrical panel. Drill a hole in the ceiling where you plan to install the bathroom fan, and where a closet is located directly above the bathroom, stopping once the drill penetrates the floor above. Go into the room above the bathroom to see exactly where the drill penetrated, and to adjust the positioning of the fan, if necessary.

Hold the bathroom vent against the ceiling, with the exhaust opening against the hole you drilled. Trace around the perimeter of the fan housing on the ceiling. Remove the fan and cut along the line you traced, using a drywall saw, and remove the drywall.

Cut a hole in the floor above where the drill bit penetrated, using a hole-saw attachment on your drill. The attachment needs to be slightly larger than the duct you plan to connect to the fans exhaust port.

Pull the electrical wiring in the subfloor above the bathroom ceiling through the electrical knockout on the side of the fan assembly. Strip 6 inches of the wirings insulation off, and then twist the same colored wires from the ceiling wire and the wires in the assembly together. Twist wire nuts onto the wires to hold the connections together, and then tighten the screws where the electrical wiring enters the fan assembly, holding it in place.

Hold the fan assembly inside the cutout you made in the ceiling, while a helper reaches through the hole in the floor above and pulls out the brackets on the sides of the fan assembly until they touch the floor joists. The helper then must drive screws through the ends of the brackets and into the floor joists.

Insert a 6-inch-long metal duct piece into the cutout in the floor and over the exhaust port in the fan assembly. Drive sheet metal screws through the sides of the duct and into the exhaust ports lip. Dangle a plumb bob from the ceiling above the duct until the plumb bob dangles over the center of the duct opening, and then mark the location of the plumb bob on the ceiling.

Cut a hole in the ceiling with the hole-saw attachment, with the mark you made on the ceiling in the middle of the hole saw. Climb into the attic through the attic-access panel, and lower a second length of metal ducting through the hole in the ceiling. Drive sheet-metal screws through the sides of the new duct piece and into the smaller duct piece, and then wrap foil duct tape around the connection.

Insert a flexible duct over the end of the duct inside the attic and slide an insulation sleeve over the duct. Tighten a hose clamp over the duct, flexible duct and insulation sleeve to secure the connection. Drive a 3-inch wood screw through the roof, from inside the attic, marking where you plan to vent the duct through the roof.

Climb onto the roof using a ladder and locate the screw coming through the roof. Hold the roof caps duct piece on the roof, with the screw in the middle, and cut around the perimeter of the duct with a utility knife. Remove the cut shingles, and then cut through the roof with a jigsaw, following the same cut line as the shingles.

Insert the duct piece for the roof cap in the hole, and then drive sheet-metal screws through the sides of the duct and into the roof. Insert the cap over the duct, and cut away any shingles that contact the hood, using the utility knife. Pick up the shingles above the cap and insert the flange below the shingles, and then apply roofing cement to the flange to attach the shingles.

Drive roofing nails through the exposed edges of the caps flange. Go back in the attic and attach the flexible duct to the duct piece in the roof using the hose clamp. Restore the electricity to the bathroom, using the electrical panel.

How to Install Bathroom Vent Pipes eHow
www.ehow.com Home Repair & Maintenance Plumbing
How to Install Bathroom Vent Pipes. Vent pipes are connected to sewer lines to allow waste gas to escape from the line. They go from the sewer line up through the ...
Overview How to Install a Bathroom Vent Fan This Old House
www.thisoldhouse.com/toh/how-to/overview/0,,689843,00.html
A bathroom without a ventilation fan is like a fireplace without a chimney: If you fail to pull the moisture generated in the bathroom out of there, it will migrate ...
Bathroom vent trap door keeps flapping and banging. How to Fix ...
www.doityourself.com Forum
A couple of months ago, I noticed that the ceiling vent blower fan in our master bathroom was not properly connected to the roof mounted gooseneck
How to Vent Bathroom Plumbing eHow
www.ehow.com Home Repair & Maintenance Plumbing
How to Vent Bathroom Plumbing. Venting bathroom plumbing is essential to proper sewer function and to allow noxious fumes to escape from the pipes. Noxious sewer ...
How Does Your Bathroom Sink Drain And Vent Pipes Work? -
www.youtube.com/watch?v=-xuhCwHMnKk
http://www.contractors.gregvan.com/ if you're looking for a contractor or thinking about hiring one in the future, click on the link above. Here's another ...
How to Install a Bathroom Vent Fan This Old House
www.thisoldhouse.com/toh/how-to/intro/0,,689843,00.html
Installing a ventilating fan in your bath will help eliminate fogged-up windows, steamy mirrors and stale odors. But more importantly, it will help prevent moisture ...
How to Replace a Bathroom Exhaust Vent Fan
www.todayshomeowner.com/.../how-to-replace-a-bathroom-exhaust-vent-fan
Bathroom exhaust vent fans are needed to remove excess humidity that can lead to mold or mildew and cause damage to your walls or ceiling. Unlike older vent fans, new ...
How to Properly Vent a Bathroom Exhaust Fan in an Attic
www.todayshomeowner.com/video/how-to-properly-vent-a-bathroom...
Bathroom exhaust fans perform an important function by removing excess moisture from your home. When venting a bathroom exhaust fan, make sure to vent the air to the ...
Do Stains on Your Ceiling or Drips From a Bathroom Vent Mean
ezinearticles.com Home Improvement Roofing
Jan 20, 2011 Do Stains on Your Ceiling or Drips From a Bathroom Vent Mean Your Roof Is Leaking? How to Find Out. By D Friesen
How to Vent a bathroom fan with This Old House Plumbing &
plumbing-n-electric.wonderhowto.com/how-to/vent-bathroom-fan-with...
Watch this video from This Old House to learn how to vent a bathroom fan. Steps:1. Screw the humidifier to a wall near the furnace. 2. Cut away insulation from the ...